Its a LILYGO T3S3 (a module focused on handheld use) stuck into a housing I modeled myself and 3d printed out of ASA plastic. It has some Chinese “high gain” 915MHz antenna inside the grain silo looking part, which is oversize to prevent too much signal reflection/distortion from the plastic being too close to the antenna. Its powered by 18ga alarm system wire that I draped down the roof to a 5v power supply on the deck. And since I’m renting, non permanent modifications only, thus the clamp to the vent pipe.
Its what I had, just to get started. Quickly realized I needed to be on my roof to get any good connections in my node-sparse area haha.
So far it’s working well, I have 13 consistent mesh connections with 3 direct connections, when before I would previously only get spotty connections to the mesh at all from inside my house.
I’ll buy some better base station hardware later, once I put one up at my girlfriend’s house a few miles away…
You got my uovote before I even read the post, just for “blackjack and hookers”.
Party on Bender!
You should totally paint that thing to look like a little barn and grain solo 😆
unironically I have red, white, black, and brown ASA available to me, and a multicolor Bambu printer… Hmmmm
I’ve been looking into Reticulum to build a resilient network that includes lora.
Hmm, very interesting. Being able to run true data over LoRa or any other radio/comm method is definitely cool but not really that useful to me I think, it’s a little too flexible. I need more of a set-and-forget service that I realistically only use for text messages. The more complex the setup, the less likely me or any of my friends are to actually adopt it- and I’m not that crazy of a digital prepper lol.
Never done meshtastic, but I do a little amateur radio. For a high gain antenna, do you just experiment with where it’s pointing, or do you point towards something in particular?
Depends on the orientation of the gain. Most “high gain” antennas are still omnidirectional, they’re just focusing the signal out into a horizontal ring, like so:

More dB, and you get a flatter donut with more horizontal reach at the expense of vertical reception. Low-gain antennas reception area starts to approach a sphere, so those don’t need to pointed up for best signal as much as higher-gain omnidirectional antennas.
Directional antennas are the ones that need to be pointed at something specific, as they have more of a cone of effect depending on the dB:

Its an omnidirectional “high gain” which is why it’s in quotes.
You can use yagi or dish directionals, but they’re a lot more difficult because 915mhz is fairly long wavelength and the antennas get big. I’d have to know the location of known good repeaters to know what to aim it at.
hey not for nothing but the clamp to a vent pipe is clever and I’m gonna use it.
Yeah, it’s very easy for anything lightweight or not too tall. Obvs these vent pipes are not anchored super well, but if you’re using something strong like a fence pole and 2 clamps at a time, you could easily hold a 4ft aerial.
My design advice, make the clamp circle the exact size of the pipe you want to attach to. The fixed side (housing) should be an exact half circle. The moving side (clamp) should be less than a half circle such that there is about 1/8" or 3mm gap between the clamp face and the housing side face. That way you get a really nice compression by stretching the plastic when you tighten the screws and it will not slip.
Get a 1W RAK!
Considering! Are those booster modules us legal?
Yes, they are. The U.S. Federal Communications Commission allows 1 watt EIRP on the ISM bands.
HAWT
The only issue you may have with the 1W is that they will be able to send to nodes that will probably not be able to contact you back. Because they are lower power.
So while you may be able to send really well, receiving may be a bit more difficult.
Ive heard of people saying that the 1W will muddy up the radio space since its basically one node “screaming” over others. Im not 100% buying it as 1W is still pretty quiet compared to other electronics in other spectrum. But thought I would mention it.
Yeah, after thinking about it 1w will probably be overkill, since the two places I can run base stations right now are not very well located. If I get a chance to put one on a hilltop I might go 1w with a big antenna for receive performance, but not right now.
US-legal yes. We use them in Canada as well but I haven’t checked if they’re legal here. They can be configured to tx at lower power. Their rx stage is also more sensitive so they’re approx balanced with the 1W tx.
Anything is a dildo if you’re brave enough.
Please do some proper cable management without duct tape. Especially on the roof, this is now very prone to be hit by a lightning.
Hey now, I forgot to bring zip ties. It’s what I had.
Also, my lightning risk is very low here, there is a mountain behind me and there are taller houses around me. Hell, this device isn’t even the tallest or least grounded thing on my own roof.
Do you have solar setup or is it direct connect within the house?
Direct connect, I have a 5v PSU plugged in under the eaves on the back deck. I was going to do solar but have no way to manage a battery without getting different hardware. Will do that later.







