I’m tried checking the plastic tubes, filter, and drain hole within the dishwasher but no clogs.

The black pipes that go into to ground are not drained since this same is used frequently everyday by my sink with no issues.

I tried scooping the water out. Turning off the breaker to the power for 30 minutes. Holding the start by to reset it.

But it will not drain the water nor do a proper cleaning. And to sanitized light flashing. It seems maybe looking for a product to start sanitize cycle maybe? We tried adding liquid to it, closing it, doing a sanitize cycle, but the same problem.

  • jagermo ( jagermo@feddit.org ) 
    link
    fedilink
    arrow-up
    10
    ·
    3 months ago

    Might be fat clogging the pump. I had this one time, called the repair company and the guy pullednojt a syringe and pushed water into a hole and a big block of fat popped out - 5 minutes work. Machine drained afterwards without an issue.

    He told me that this frequently happens when people only use the low temperature program and that you should run the high temp program (70c) at least twice a month.

  • poVoq ( poVoq@slrpnk.net ) 
    link
    fedilink
    arrow-up
    6
    ·
    3 months ago

    You can buy a special dishwasher cleaning powder that can better deal with fat build up in the internal drain. Sometimes that helps and it is the least messy option.

  • mlfh ( mlfh@lm.mlfh.org ) 
    link
    fedilink
    English
    arrow-up
    5
    ·
    3 months ago

    Does the motor/pump work at all, spraying water around inside? If yes, and there are no clogs, check the drain solenoid - it should actuate a valve that directs the pumped flow of water through the drain pipe instead of the sprayers.

      • AbidingOhmsLaw ( AbidingOhmsLaw@lemmy.ml ) 
        link
        fedilink
        English
        arrow-up
        3
        ·
        edit-2
        3 months ago

        Look for your brand / model sevice manual on-line, it should have troubleshooting and testing procedures as well as part # lists and replacement guides.

        In the user manual I found this. Searched “Bosch Silence Plus 50 user guide”. Since they made multiple models with this name, get the model number off of the sticker on the right side on the door to refine the search.

        Large food remnants in the rinsing water not
        retained by the filters may block the waste
        water pump. 
        In this case:
        • Disconnect the appliance from the power supply. 
        • Remove the filters (see Figures 11-12).
        • Scoop out standing water - use a sponge if
        necessary.
        • Using a spoon, pry off the pump cover (see Fig-
        ures 14-15) until it clicks, then grip the cover
        and pull upward until it resists and then pull
        forward.
        • Check inner compartment and remove any for-
        eign objects.
        • Place cover in the original position, press
        down and engage.
        • Reinstall filters.
        
  • bstix ( bstix@feddit.dk ) 
    link
    fedilink
    arrow-up
    5
    ·
    3 months ago

    Mine has a sensor in the drain much further down than the filter. If someone spilled detergent inside the machine, it will make a lot of bubbles, and this is enough to trigger the sensor, so it refuses to run the pump.

    In order to flush it, I need to move it out, so I can open the safety drain on the back and throw in a bucket of water, collecting the water from the safety drain on a towel.

  • nomad ( Nomad@infosec.pub ) 
    link
    fedilink
    arrow-up
    5
    ·
    3 months ago

    Drain it and disassemble in the bottom until you find a metal ball in front of a whole. Both maybe the size of a marble. You won’t probably be able to remove the ball, but clean around it and make sure its not stuck. I found all kinds of stuff there. Alcohol or dish washing soap help with the fat and stuff.

      • FiniteBanjo ( FiniteBanjo@feddit.online ) 
        link
        fedilink
        English
        arrow-up
        4
        ·
        3 months ago

        They sell what’s called “plumbing snake”, cheapest is about $10, maybe that could reach further. I think the commenter before was alluding to moving the unit out from the wall and checking the back of it, but before doing so switch off as many breakers as you can because the appliance will be hardwired and in fact you might not be able to even pull it out until after you’ve disconnected the wires by hand.

        • dudesss ( dudesss@piefed.ca ) OP
          link
          fedilink
          English
          arrow-up
          4
          ·
          3 months ago

          Thank you. I have moved the unit from the wall, and was able to blow the water from the tube into the drain. So I think its something to do with within the dishwasher itself.

  • P13 ( P13@lemmy.dbzer0.com ) 
    link
    fedilink
    arrow-up
    4
    ·
    3 months ago

    There are two pumps in a dishwasher: drain and circulation. Each has a capacitor which can be replaced if it blows. In my 25+ year old dishwasher, this is the only thing that breaks from time to time.

    Should be less than 10 bucks including shipping.

    Edit: sounds like some models use a solenoid with one pump instead. Open the machine and investigate.

  • CompactFlax ( CompactFlax@discuss.tchncs.de ) 
    link
    fedilink
    English
    arrow-up
    3
    ·
    3 months ago

    Failed drain pump seems the most likely scenario, if you’re absolutely proven the pipes are clear - the drain pipe runs through the dishwasher and then cabinetry to the sink drain, and it can be a circuitous path that traps grease.

  • geekwithsoul ( geekwithsoul@piefed.social ) 
    link
    fedilink
    English
    arrow-up
    3
    ·
    3 months ago

    Have the exact same dishwasher and had a similar problem at the beginning of the year. After days of troubleshooting, ended up having to call for a repair unfortunately. I believe in our case it was both the pump and impeller (the parts that take the water/sludge and get them out of the dishwasher, not the water filling it)

  • sanzky ( sanzky@beehaw.org ) 
    link
    fedilink
    arrow-up
    3
    ·
    3 months ago

    if you’ve checked all the basics. the issue is most likely the pump.

    I changed mine. it is not particularly hard. took me 40m with a youtube video

  • The thing I learned when I had dishwasher issues was to always start with the manual. You’ll probably be surprised with how much info is in the manual.

    The Samsung dishwasher I had issues with had 50+ pages worth of diagnostics and repair instructions, including detailed meanings for every unique error code that can occur, and instructions for putting the whole unit into a test mode, where you can force each motor to run independently, run test routines for sensors, etc. Gave me everything I could want for DIY repairs.

    Can’t say it’s always this nice, of course, but this adivce has served me well for other appliances since.