The 240-120 voltage problem can be remedied by using transformers but that doesn’t negate the frequency difference between grids. Australia operates on 230v @ 50Hz while the US works with 120V @ 60Hz for instance, as certain electronics that are singular voltage (Hair Dryers, Desk Fans or Electric Blankets) have their frequencies disclosed even if the voltage on those are different than the one that country uses.

Does plugging in a device that has 120v-60Hz via a transformer on a grid that operates on 230v-50Hz ruin the device due to either heating elements or motors inside? Even between countries that work with 220-40v but one uses 50Hz while the other uses 60Hz, does that render those electronics (like dehumidifiers, power drills, curling irons) incompatible despite them using similar voltage (like 220v vs 230v)?

  • JustEnoughDucks ( JustEnoughDucks@slrpnk.net ) 
    link
    fedilink
    English
    arrow-up
    5
    ·
    4 months ago

    Anything with a motor will run differently, usually safely but not always.

    Motor speed is 120*frequency/poles.

    For example, a 4 pole hair dryer motor will run at 60Hz, the fan will run at around 1700-1750rpm instead of 1400-1450rpm.

    For fans specifically, this can be a problem because fan load (torque) increases to the third power with respect to speed. This means that changing the frequency to 60Hz for a fan designed for 50Hz will run it at a significantly higher load which can make it run at a worse point of the torque curve where it is less efficient and ultimately overheat.

    Some electronics have filters based on their designed operating frequency, so signals may get distorted by switching frequencies (notch filters on sensitive signal chain things like ECGs devices) though many are designed for both nowadays.

    Things like electric blankets are just resistive loads so there would be little effect, but if they have very cheap electronics it is possible that the timer functions would be analog AC coupled so the timers might run fast or slow.

  • farmgineer ( farmgineer@nord.pub ) 
    link
    fedilink
    English
    arrow-up
    3
    ·
    4 months ago

    Japan is split and has both 50 and 60hz grids. Modern products don’t have any issues with this (voltage is 100v typically). In the older days, this was an issue for things with clocks and motors from what I understand, but I didn’t move here u til the 2010s

    • kELAL ( kELAL@lemmy.blahaj.zone ) 
      link
      fedilink
      English
      arrow-up
      1
      ·
      4 months ago

      It helps a lot that appliances for the Japanese domestic were designed to cope with different frequencies (for better or worse) from day one, as it’s cheaper than having two almost identical product ranges. Motor and transformer windings designed to tolerate the extra current when running @ 50Hz, or switchable winding taps if efficiency mattered. Different pulleys / switchable gears for things where speed matters, like record players and electro-mechanical clocks.

    • CovertHammer ( animemann80@feddit.online ) OP
      link
      fedilink
      English
      arrow-up
      5
      ·
      4 months ago

      I know that 60Hz is faster than 50Hz, since I’ve shipped an air fryer from a country with 50Hz (type I plug) to a family friend who lives in one where 60Hz is used (has a type B outlet) but they used an adapter. There were issues with the heat element, as it turns out their food is overcooked despite us having miminal differences with voltage (230 vs 220).

      • CameronDev ( CameronDev@programming.dev ) 
        link
        fedilink
        English
        arrow-up
        4
        ·
        edit-2
        4 months ago

        At most, i would expect the fan in the airfryer to spin faster, but i don’t believe there is a relationship between frequency and power.

        Resistive heating elements in airfryers should also be unaffected by frequency.

        My guess is that heating element is tuned for 220v, but at 230v it goes to a much higher temperature? Or they suck at cooking :)

        Edit: thinking more, a 20% faster fan could definitely be the issue.

  • Generally, you won’t ruin it. Modern stuff with switching power supplies like laptops handle the difference automatically. Old motor-driven devices like record players may speed up or slow down depending on their rating, and large AC induction motors, like washing machines, might heat up slightly.

  • xia ( xia@lemmy.ca ) 
    link
    fedilink
    English
    arrow-up
    1
    ·
    4 months ago

    Some time ago, I ran across a frequency converter product meant for professional barbers to use overseas hair clippers. Apparently they are designed to oscillate with the mains frequency, and tear themselves apart when run with the wrong frequency?