variants_of_concern ( @variants_of_concern@lemmy.one ) English58•8 months agoTorx >
UntouchedWagons ( @UntouchedWagons@lemmy.ca ) English10•8 months agoRobertson is top tier too
Seven ( @7of9@startrek.website ) 2•8 months agoI find Torx unpleasant to work with.
averyminya ( @averyminya@beehaw.org ) 3•8 months agoI’d like Torx if when they got used they didn’t torque the shit out of the screws. Only the Steam Controller has ever been a simple process of removing Torx screws.
Everything else takes the power of drawing Excalibur from its stone.
Seven ( @7of9@startrek.website ) 3•8 months agoFor me, it’s how the key feels in the head. It doesn’t go in far enough that you can let the key just sit there on it’s own like with a hex head.
averyminya ( @averyminya@beehaw.org ) 2•8 months agoI hate that too, I feel like I have that issue with Philips as well. In fact, I was struggling with it just today
Seven ( @7of9@startrek.website ) 2•8 months agoThe flipside to that is when you’ve got a JIS driver and when you’re done it doesn’t want to let go of the screw. Very satisfying, possibly sexual.
variants_of_concern ( @variants_of_concern@lemmy.one ) English1•8 months agoI guess it just depends on your tools, I prefer torx over hex because it feels much more solid and less likely to strip out if it’s a cheap screw, I worked on a product that had the outside screws there were supposed to look nice use these hex heads made of butter haha but the rest of the appliance used all torx of the same size head
Seven ( @7of9@startrek.website ) 1•8 months agoMaybe, I only work with high tensile stuff and occasionally stainless, so I’ve never had issues with hex heads (that weren’t caused by misuse)
averyminya ( @averyminya@beehaw.org ) 1•8 months agoJiggling it like you’re getting the last few drops from the gas pump…
Seven ( @7of9@startrek.website ) 2•8 months agoThat’s more of a tapping motion for me, but everyone has different needs and who am I to judge?
sigmaklimgrindset ( @sigmaklimgrindset@sopuli.xyz ) 51•8 months agoMe out here calling them “plus head” and “minus head” like a neanderthal
isolatedscotch ( @isolatedscotch@discuss.tchncs.de ) 11•8 months agowe call philips “cross” and flathead “slit”
milicent_bystandr ( @milicent_bystandr@lemm.ee ) 4•8 months ago‘cross-head’ and ‘flat-head’ for me
30p87 ( @30p87@feddit.de ) 1•8 months agoThen there’s german, with (technically) slit and cross-slit
Kreuzschlitzschraubendreher
cuacamole ( @cuacamole@feddit.de ) 2•8 months agoKreuzschlitz gibt’s net. Entweder Kreuz oder Schlitz.
30p87 ( @30p87@feddit.de ) 1•8 months agoISO 8764-1 Schraubwerkzeuge – Schraubendreher für Schrauben mit Kreuzschlitz – Teil 1: Schraubendreherspitzen.
User ( @creation7758@lemmy.ml ) 2•8 months agoNeanderthals were on to something then
Tony! Toni! Toné! ☑️ ( @TonyToniToneOfficial@lemmy.ml ) 46•8 months agoomg I’ve found my people, you all have strong opinions on screw driver geometry
UntouchedWagons ( @UntouchedWagons@lemmy.ca ) English4•8 months agoTorx and Robertson are the best.
AlexWIWA ( @AlexWIWA@lemmy.ml ) English2•8 months agoI always know I’ve found my people when they have extremely strong beliefs on everyday household items. My favorite was a 3 week argument about electrical sockets on Reddit a few years ago
Pyr_Pressure ( @Pyr_Pressure@lemmy.ca ) 31•8 months agoI fucking hate Phillips style so much.
Never tried JIS though, Robertson is where it’s at.
Troy ( @troyunrau@lemmy.ca ) 12•8 months agoFound the Canadian
Overzeetop ( @Overzeetop@sopuli.xyz ) 5•8 months agoBut not #1, or most of #2, in common stainless alloys. Even dry film lubed and drill tip is insufficient to prevent the torque from exceeding the (relatively low) yield strength, leading to stripped screws from standard driving in any wood denser than about G=0.45. There’s simply not enough contact area to prevent it.
s_s ( @s_s@lemmy.one ) 1•8 months agoStainless fasteners are niche and require stainless tools, full-stop.
Most fasteners are not stainless.
Overzeetop ( @Overzeetop@sopuli.xyz ) 2•8 months agorequire stainless tools
You really don’t want to use stainless tools as they will plastically deform. Roberson is just not that great for torque-transfer geometry; it’s advantages lie elsewhere.
s_s ( @s_s@lemmy.one ) 1•8 months agoYou really don’t want to use stainless tools as they will plastically deform
They are made specifically for stainless fasteners.
You’ll frequently find them in the toolbags of aerospace professionals and industrial electricians and they are really the only folks that deal with a lot of stainless fasteners.
Bicycle and motorbike folks have lots of stainless hardware, too. And lots of time you’ll see folks blame JIS/Phillips on ruining their fasteners, but sometimes it’s just because they’re using toolsteel tools on stainless fasteners.
lnxtx ( @lnxtx@feddit.nl ) 17•8 months agoPozidriv enters the chat
bobs_monkey ( @bobs_monkey@lemm.ee ) 5•8 months agoHow does a positraction on a Plymouth work? It just does.
mxcory ( @mxcory@lemmy.blahaj.zone ) English2•8 months agoI wonder how many pozidriv screws have been stripped and a Phillips driver has gotten the blame.
lazynooblet ( @lazynooblet@lazysoci.al ) English14•8 months agoI’m trying to understand what the top half of each diagram is
prof ( @prof@infosec.pub ) 8•8 months agoTaco
grooving ( @grooving@lemmy.studio ) 13•8 months agoScrew this meme
Scary le Poo ( @Scary_le_Poo@beehaw.org ) 12•8 months agoTorx is superior in every single way.
Mongostein ( @Mongostein@lemmy.ca ) 4•8 months agoTorx blows. Robertson’s where it’s at.
Scary le Poo ( @Scary_le_Poo@beehaw.org ) 1•8 months agoRobertson has the issue of when force is applied it is at angles that can easily damage the head and the tool or both.
In general I feel Robertson is excellent for low torque applications, but torx doesn’t have any of these issues.
Akasazh ( @Akasazh@feddit.nl ) 6•8 months agoAww Jis
s_s ( @s_s@lemmy.one ) 6•8 months agoPozidriv > *
Not only is it self-centering like phillips and JIS (eg the reason they are used in so many line-assembled manufactured goods) but it’s has superior contact like a Robertson (square drive) or hex or torx.
FleetingTit ( @FleetingTit@feddit.de ) 2•8 months agoTorx > *
s_s ( @s_s@lemmy.one ) 3•8 months agoTorx’s highest-in-class leverage without camming out gives it superiority in some applications (eg impact-rated deck screws), but if you had to choose one fastener head for everything, posidriv is it.
Torx is not self-centering, and therefore inappropriate for many tasks including anything not hand-assembled. It is also susceptible to stripping out after rusting.
Isn’t it proprietary?
s_s ( @s_s@lemmy.one ) 6•8 months agoThe patent is expired and it now has ANSI and ISO standards.
WoefKat ( @WoefKat@lemmy.ml ) 5•8 months agoThat guy loves jis lol
Salvo ( @Salvo@aussie.zone ) English2•8 months agoIt’s not about the depth, it’s all about the angle.
Overzeetop ( @Overzeetop@sopuli.xyz ) 3•8 months agoSounds like someone is working with a small screwdriver, if you ask me.
spudwart ( @spudwart@spudwart.com ) English2•8 months agoRespect
promitheas ( @promitheas@iusearchlinux.fyi ) 2•8 months agohttps://piped.video/watch?v=IAtOKl3JlnQ&t=970
Around the 16:05 mark. Im not a screw connoisseur but I remember this clip :)